top of page

Home  /  Ovens for PVC, Rubber & Plastic Product Makers

Ovens for PVC, Rubber & Plastic Product Makers

PVC, rubber and plastics processors rely on controlled heat. Plastisol is fused in moulds and on dipped parts, rubber and silicone parts are post-cured to drive off by-products, plastic sheet is heated before forming, and granules are dried before moulding. These materials are sensitive. A few degrees too cold leaves plastisol weak, and a few degrees too hot discolours it or scorches the part. That is why airflow and temperature control matter more than raw heating power.

 

Advance Heating Systems builds PVC curing ovens in conveyor and batch form, cooling conveyors, heated vacuum chambers, and sheet heating ovens for hot forming. Repeat buyers in the PVC moulding trade have returned for more ovens over the years. Ovens are electric, LPG, PNG or CNG heated.

Equipment we build for this industry

Conveyor or batch oven for gelling and curing PVC plastisol in moulds, mats, labels and coated parts.

Electrically heated vacuum chamber for de-airing, low-temperature drying and process work under vacuum.

Oven for vulcanising rubber parts, hoses and profiles to set their final properties.

Oven for post-curing silicone rubber parts to remove volatiles and stabilise properties.

Oven for heating plastic sheets until soft enough to form.

Dryer for removing moisture from plastic granules before moulding.

How we help PVC, Rubber & Plastic Product Makers

Heating processes in this industry

  • PVC plastisol fusion: AHS PVC ovens typically work at about 200°C, with fusion temperature per paste data sheet

  • Peroxide-cured silicone post-cure: about 200–250°C for 2–4 hours

  • Platinum-cured silicone post-cure: about 150–180°C for 1–2 hours

  • FKM rubber post-cure: about 150–200°C for 2–3 hours

  • Dip moulding: mould pre-heated, dipped, then fused or cured; a hotter mould builds a thicker coat

  • Sheet heating for hot forming: multi-tier ovens with side-chamber finned heaters

  • Mould cooling: cooling conveyor with hood and fan, or water-cooled conveyor

 

Challenges we help solve

  • Temperature sensitivity: plastisol and silicones need tight control and even airflow, not just heat

  • Volatiles: post-curing and plastisol fusion release fumes that must be exhausted

  • Gas supply: after the 2026 West Asia disruption, industrial gas was curtailed and sold at spot rates, and propane prices roughly doubled in some clusters

  • NCR clean-fuel rules: units in Delhi NCR must use fuels on the CAQM approved list

  • Emission limits: particulate limit for targeted NCR industries falls to 50 mg/Nm³ from 1 Oct 2026; clean-fuel-only units can seek exemption

 

Why manufacturers choose Advance Heating Systems

  • 13 PVC and plastic curing buyers in our sales records since 2017, several with repeat orders

  • Conveyor PVC lines with heating, cooling and optional water-cooled mould conveyors

  • Sheet heating ovens for hot forming at common ratings of 15 kW and 18 kW

  • Heated vacuum chambers with ±1°C PLC profile control

  • Electric, LPG, PNG and CNG heating

  • Building ovens in Delhi since 1991

 

More equipment for this industry

 

Common questions

What temperature does PVC plastisol need?

AHS PVC ovens typically run at about 200°C. Check the fusion temperature on your paste supplier's data sheet.

 

Conveyor or batch oven?

Conveyor ovens suit steady output of similar moulds. Batch ovens suit large parts and low volume.

 

Can you supply cooling with the oven?

Yes. We supply cooling zones with hoods and fans, and water-cooled mould conveyors.

 

Do you build silicone post-curing ovens?

Yes. Post-curing needs even hot air and good exhaust. See our Silicone Post Curing Oven.

 

Is an electric oven practical?

Yes. Electric PVC ovens start at about 18 kW.

 

Planning a new line or replacing an old oven? Tell us your product, batch size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120 or send an enquiry.

bottom of page