top of page

Home  /  Products  /  PVC Curing Oven

PVC Curing Oven

Conveyor or batch oven for gelling and curing PVC plastisol in moulds, mats, labels and coated parts.

Also called a plastisol curing oven, PVC moulding oven or PVC mat curing oven.

Photo shown is a representative image.

Key Features

  • Even airflow over moulds for complete fusion

  • Burner-fail alarm on gas models

  • Variable conveyor speed to set cure time

  • Cooling section with hood and fan

  • Optional water-cooled mould conveyor

  • Batch or continuous layouts

Specifications

Working temperature: typically about 200°C

Maximum rating: 250–450°C depending on build

Type: conveyor (continuous) or batch trolley

Example conveyor: 2,500 mm heating + 3,000 mm cooling zone

Electric heating: from about 18 kW

Gas heating: LPG/PNG/CNG burner in a firing chamber

Insulation: 75–125 mm mineral wool / ceramic fibre

Drive: DC or VFD variable speed

Options: water-cooling conveyor for moulds, cooling hood with fan

Industries: PVC, rubber and plastics, automotive accessories, labels

About the PVC Curing Oven

PVC plastisol is a liquid paste of PVC resin and plasticiser. It only becomes a tough, flexible solid when it is heated to fuse. A PVC curing oven supplies that heat to filled moulds, dipped parts or coated products. The paste has to reach fusion temperature right through its thickness. Too little heat leaves it weak and cheesy, and too much discolours it. That is why the oven needs close control around its working point, which is typically about 200°C, and even airflow over every mould.

 

AHS builds PVC curing ovens in two forms. Conveyor ovens suit steady production of moulded items such as car mats, labels, key chains and soft PVC goods. One car-mat line had a 2,500 mm heating zone and a 3,000 mm cooling zone with a 1,500 mm hood and 10-inch fan. It was LPG fired, with a single burner in a firing chamber, a burner-fail alarm and a DC drive, plus an optional water-cooling conveyor for the moulds. Batch trolley ovens suit lower volumes or larger parts. Electric ovens start at about 18 kW. Maximum ratings run from 250°C to 450°C depending on the build, with 75–125 mm mineral or ceramic wool insulation.

 

Repeat buyers in the PVC moulding trade have come back to AHS for more of these ovens, for cooling conveyors and for a vacuum chamber oven. See also our Vacuum Chamber and the Plastic Annealing Oven. Tell us your mould size, number of moulds per hour and how you load them, and we will propose conveyor width, zone lengths and heating.

 

Typical applications

  • Curing PVC car mats and floor mats

  • Curing PVC labels, patches and key chains

  • Fusing PVC dip-coated tool handles and grips

  • Curing plastisol-filled moulds for soft PVC goods

  • Curing PVC coatings on wire products

 

Common questions

What temperature cures PVC plastisol?

Most plastisols fuse at around 180–200°C. Check the paste supplier's data sheet, and remember the full thickness must reach that temperature.

 

Should I buy a conveyor or batch oven?

A conveyor suits steady output of similar moulds. A batch oven suits low volume, large parts or frequent changes.

 

How do I cool the moulds after curing?

We add a cooling zone with hood and fan, and an optional water-cooling conveyor so moulds can be stripped quickly.

 

Can you also supply a vacuum chamber?

Yes. See our Vacuum Chamber page for heated vacuum chambers used alongside PVC lines.

 

Is an electric version available?

Yes. Electric ovens start at about 18 kW, and LPG, PNG and CNG versions are also built.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page