top of page

Home  /  Ovens & Furnaces for Aluminium Circle & Sheet Makers

Ovens & Furnaces for Aluminium Circle & Sheet Makers

Aluminium circle and sheet makers turn ingot and scrap into cold-rolled sheet, punch it into circles, and then anneal the circles soft enough for utensil makers to deep draw. Most of the cost is heat. Metal is melted for casting, rolled stock is annealed, and dross is skimmed off at every melt. An oven that leaves the centre of the stack under-annealed causes cracked circles at the customer, and a melting furnace that runs too hot burns metal into dross.

 

Aluminium annealing is the largest product family in the Advance Heating Systems archive. We have built trolley-type circle annealing ovens from 500 kg to about 4,000 kg per charge, melting furnaces from 100 kg to 1,000 kg, and dross extraction systems that recover metal from hot skimmings beside the furnace. Every machine is offered with electric, LPG, PNG or CNG heating, or dual mode with both.

Equipment we build for this industry

Trolley-type oven for annealing stacks of aluminium circles soft for deep drawing, 500 kg to 4,000 kg loads.

Box, bogie or pit furnace for annealing steel, brass, copper and aluminium foil, up to 1,200°C.

Oven for artificial ageing (T5/T6) of aluminium extrusions and castings, with tight temperature uniformity for consistent strength.

Furnace that heats aluminium parts to solution temperature before quenching and ageing.

Oven that brings aluminium billets to extrusion temperature evenly before pressing.

Gas or electric melting furnace for aluminium and non-ferrous scrap and ingots, 100–1,000 kg per charge.

How we help Aluminium Circle & Sheet Makers

Heating processes in this industry

  • Circle and sheet annealing: about 340–410°C, soaked until the whole stack recrystallises to soft O temper for deep drawing

  • Recovery (partial softening): from about 90–120°C up to 230°C, used for partial tempers

  • Melting ingot and scrap: up to about 800°C for casting slabs and strip

  • Dross recovery: hot dross worked in a heated vessel so trapped aluminium drains out

  • Ageing of heat-treatable alloys: about 150–200°C after solution treatment at about 500–540°C

  • Billet preheating before extrusion: temperature set by alloy and press practice

 

Challenges we help solve

  • Energy cost: aluminium extruders reported energy costs up about 30% and raw material up 30–40% after the 2026 West Asia (Hormuz) disruption (ALEMAI, Sep 2026)

  • Gas supply: in March 2026 one city gas distributor asked industrial users to cut to 40% of contracted gas and charged the excess at spot rates

  • Power tariffs: Haryana industry has quoted about Rs 11/unit for power (2019), which raises the cost of electric annealing

  • NCR clean-fuel rules: the CAQM approved fuel list applies across Delhi NCR, and Delhi prohibits furnace oil, coal and pet coke for industry

  • Emission limits: CAQM directions cut the particulate limit for targeted industries from 80 to 50 mg/Nm³ from 1 Oct 2026; units on clean fuels only can seek exemption

  • Carbon rules: secondary aluminium was brought under the Carbon Credit Trading Scheme intensity targets in January 2026

  • Quality: incomplete soak at the centre of dense stacks leads to cracking in deep drawing

 

Why manufacturers choose Advance Heating Systems

  • Aluminium annealing is our largest family: more than 550 documents on circle annealing ovens between 2004 and 2026

  • Close to 60 aluminium circle and utensil annealing buyers in our sales records since 2017

  • Charges from 500 kg to about 4,000 kg, with 500 kg and 600 kg our most-built sizes

  • More than 100 documents on dross extraction and aluminium recovery systems since 2012

  • Electric, LPG, PNG, CNG and dual-mode heating, and conversion of existing furnaces to gas

  • Designing and building industrial ovens in Delhi since 1991

 

More equipment for this industry

 

Common questions

What temperature should aluminium circles be annealed at?

Fully soft O temper is usually reached at about 340–410°C, held until the coldest part of the stack is at temperature. The exact cycle depends on alloy and degree of cold work.

 

What charge size do you build?

500 kg and 600 kg are most common. We have built ovens for about 4,000 kg per charge.

 

Should I choose gas or electric heating after the 2026 gas shortages?

Many plants now prefer dual mode: gas for normal running, with electric heating as a backup when gas is curtailed. We can quote all three options.

 

Can you recover metal from our dross?

Yes. Our dross extraction system treats hot dross beside the melting furnace and taps off the recovered aluminium.

 

Do your ovens meet NCR clean-fuel rules?

We offer electric, PNG, LPG and CNG heating, which are clean fuels under the NCR approved fuel list. Check your own consent conditions with the pollution board.

 

Planning a new line or replacing an old oven? Tell us your product, batch size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120 or send an enquiry.

bottom of page