top of page

Home  /  Products  /  Bogie Hearth Furnace

Bogie Hearth Furnace

Car-bottom furnace for annealing, normalising and hardening heavy forgings and castings, up to 1,200°C.

Also called a car-bottom furnace, trolley furnace or bogie type bhatti.

Key Features

  • Crane loading outside the furnace

  • Two-bogie option for continuous working

  • Multi-zone control for long loads

  • Low outer-wall temperature saves heat

  • Erection and commissioning by AHS

  • Recorder for heat treatment certificates

Specifications

Maximum temperature: 1,000–1,200°C

Example: 7,000 × 1,800 × 1,200 mm inside, 3 zones, 500–950°C within ±5°C

Loading: refractory-lined bogie on rails; two-bogie layouts

Heating: automatic LPG/PNG/CNG burners or electric elements

Airflow: AISI-304/310 radial fans with water-cooled assemblies

Lining: 75–250 mm ceramic fibre + 230 mm insulation brick

Door: lift-and-swing with seal

Outer wall: within about 25°C of ambient (example build)

Controls: multi-zone PID with recorder

Industries: Steel forging and casting, power and hydro equipment, heavy engineering

About the Bogie Hearth Furnace

Heavy forgings, castings, rolls and fabrications are too big and heavy to push into a box furnace. In a bogie hearth furnace, also called a car-bottom furnace, the hearth is a refractory-lined bogie on rails. It is loaded by crane outside the furnace, rolled in, sealed against the door and heated. After the cycle it rolls out again for unloading or quenching. One furnace can handle loads of several tonnes, and a second bogie lets you load the next charge while the first is heating.

 

AHS has built bogie hearth furnaces for steel, power and hydro-engineering users, with more than 120 documents in our files. Designs are rated to 1,000–1,200°C and use multiple automatic burners or electric elements across several zones. AISI-304 or AISI-310 radial fans with water-cooled assemblies give even heating at lower temperatures. Linings combine 75–250 mm ceramic fibre with 230 mm insulation bricks, and the door is a lift-and-swing type. One recent bogie furnace for an export buyer had an inside size of 7,000 × 1,800 × 1,200 mm and three zones. It worked from 500°C to 950°C within ±5°C, with two bogies, and its outer wall stayed within 25°C of ambient. Heating is LPG, PNG, CNG or electric. AHS carries out erection and commissioning.

 

This page is for general heavy heat treatment: annealing, normalising, hardening and high-temperature work. For post-weld heat treatment and stress relief of fabrications at lower temperatures, see also our Stress Relieving Bogie Hearth Furnace. Tell us the largest job size and weight, the cycle, and the fuel at your site.

 

Typical applications

  • Annealing and normalising heavy forgings

  • Hardening large castings and rolls

  • Heat treating hydro and power plant parts

  • Annealing large fabrications

  • Heat treating die blocks and shafts

 

Common questions

What loads can a bogie hearth furnace take?

Loads of several tonnes, limited by bogie size and rail strength. We size the bogie to your heaviest job.

 

How even is the temperature?

Our recent multi-zone bogie furnace held ±5°C across a 500–950°C working range.

 

What is the difference from a stress relieving bogie hearth furnace?

This furnace is for high-temperature heat treatment. The Stress Relieving Bogie Hearth Furnace is optimised for lower-temperature PWHT of fabrications.

 

Gas or electric?

Both. Gas burners suit large furnaces, and electric heating suits sites with good power or clean-fuel rules.

 

Do you install the furnace?

Yes. AHS carries out erection and commissioning at site.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page