top of page

Home  /  Products  /  Tile Dryer Oven

Tile Dryer Oven

Batch or conveyor hot air dryer that removes moisture from ceramic tiles and ceramic parts before glazing or firing.

Also called a ceramic tile dryer, tile drying oven, tile drying chamber or ceramic dryer.

Photo shown is a representative image.

Key Features

  • Gentle start and controlled ramp to avoid cracks and warping

  • Even airflow between every tile on the rack

  • Moisture exhaust for faster drying

  • Programmable drying profile with cycle timer

  • Trolleys and racks made to your tile sizes

  • Electric, LPG/PNG or dual fuel heating

  • Batch or conveyor designs

Specifications

Type: batch trolley or shelf oven; conveyor dryer on request

Working temperature: up to about 250°C, set to tile body

Typical drying profile: gentle start at about 60–80°C, ramp to 150–250°C

Moisture target: typically below 1% residual before glazing or firing

Heating: electric, LPG/PNG burner in firing chamber, or dual fuel

Air circulation: fans sized for even airflow between tiles

Moisture exhaust: adjustable damper or exhaust fan

Control: digital PID with timer; programmable ramp optional

Insulation: ceramic fibre and mineral wool

Trolleys and racks: made to tile size

Industries: Ceramic tiles, ceramics, refractories, clay products

About the Tile Dryer Oven

Pressed ceramic tiles typically leave the press holding about 4–8% moisture, and glazed or cast pieces pick up more water on the way. If that water is still inside when the tile reaches the kiln, it turns to steam and can crack, warp or blister the body. A tile dryer oven removes it with controlled, recirculating hot air, so tiles go on to glazing or firing dry and strong enough to handle.

 

Large tile plants use horizontal multi-layer roller dryers or vertical basket dryers placed in line with the press and kiln. AHS builds the batch trolley and shelf ovens, and compact conveyor dryers, that suit small and mid-size plants, decorative tile units and refractory makers. Construction follows our standard hot air design: an insulated MS or SS chamber, electric heaters or an LPG/PNG burner in a separate firing chamber, circulation fans that push air between every tile, a moisture exhaust damper and digital PID control with a cycle timer. Trolleys and racks are made to your tile sizes.

 

Drying has to start gently and finish hotter. A batch cycle typically begins around 60–80°C with the exhaust open to carry off moisture, then ramps toward 150–250°C to bring residual moisture well below 1%. A programmable controller runs this ramp automatically, so the outer face does not dry and shrink ahead of the core. The exact profile, airflow and cycle time are agreed with you for each tile body and thickness, usually after a trial cycle.

 

AHS supplied a tile dryer oven to a tile maker in 2026. Dual fuel heating, with electric heaters and a gas burner in one oven, is available where power or gas supply is uncertain, and larger lines can be built from our conveyor oven designs.

 

Typical applications

  • Pressed ceramic and vitrified tiles before glazing or firing

  • Glazed tiles after glazing

  • Decorative and handmade tiles

  • Refractory bricks and shapes

  • Terracotta and clay products

  • Sanitary-ware and ceramic parts

 

Common questions

What temperature do tiles need?

It depends on the tile body, thickness and moisture. Drying typically starts at about 60–80°C and rises toward 150–250°C. We agree the profile with you before the oven is built.

 

How dry should tiles be before the kiln?

Tiles are typically dried to below about 1% residual moisture before glazing or firing. Your kiln and glaze practice decide the exact figure.

 

How long does drying take?

It depends on starting moisture, thickness and load. A trial cycle is used to set the timer and ramp for each product.

 

Will tiles crack in the oven?

Most cracking comes from heating too fast or uneven airflow. A gentle start, controlled ramp and racks that let air pass between tiles prevent it.

 

Gas, electric or dual fuel?

All three are available. LPG or PNG costs less to run on larger ovens, electric suits small ovens, and dual fuel keeps you running if one supply fails.

 

Can the oven use kiln waste heat?

In some layouts hot air from a kiln can be ducted in. We check its temperature and cleanliness before suggesting it.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page