top of page

Home  /  Products  /  Chemical Dryer

Chemical Dryer

Gas-heated rotary or batch dryer for chemical powders, salts, oxides and granules, ambient to 150°C.

Also called a rotary dryer for chemicals or powder dryer.

Key Features

  • Continuous feed and discharge

  • Stainless-steel drum and contact parts

  • Indirect firing option to protect the product

  • VFD control of feed and drum speed

  • Overshoot safety controller

  • Multi-zone heating for gentle drying profiles

Specifications

Working range: ambient to 100–150°C (as per product)

Type: rotary drum (continuous) or batch

Example burner: automatic LPG, 2,00,000 kcal/hr

Drum: 3 mm SS-304 or SS-310

Feed: hopper with VFD screw conveyor; chute discharge

Zones: single or multi-zone (e.g. 3 burners, 3 zones)

Insulation: 75–150 mm rock fibre / ceramic fibre

Safety: overshoot safety controller, burner management

Drives: AC drives with speed control

Industries: Chemicals, metal powders, pigments, minerals

About the Chemical Dryer

Chemical plants often need to dry powders, crystals, salts, oxides and granules after filtration or washing, at a controlled low temperature, without contaminating the product. A chemical dryer does this either continuously or in batches. Continuous drying uses a rotary drum. Wet feed enters at one end, flights inside the turning drum lift it and shower it through hot air, and dry product leaves at the other end.

 

AHS has built gas-heated rotary dryers for chemical and metal-powder users. One 2025 zinc dryer used an automatic LPG burner of 2,00,000 kcal/hr, hopper feeding through a screw conveyor with VFD, chute discharge and a 3 mm SS-304 drum. It was rated for 150°C and worked from ambient to 100°C, with a safety controller against overshoot, 75 mm rock-fibre insulation and AC drives. Another rotary dryer had an SS-310 drum with three burners, three zones and three fans, insulated with 150 mm ceramic fibre and rock wool. Drums and contact parts are stainless steel, and firing is indirect where the product must not see flue gas. LPG, PNG and CNG are offered, as is electric heating for smaller duties.

 

For small batches, or material that must stay still on trays, see also our Tray Dryer. For drying aluminium chips and swarf, see the Aluminium Chips Dryer. Dust from fine powders is handled by a cyclone or filter at the exhaust, sized to the product. Send us the material, feed rate, moisture in and out and the maximum product temperature, and we will propose drum size, burner rating and feed system.

 

Typical applications

  • Drying zinc and metal powders

  • Drying chemical salts and crystals

  • Drying oxides and pigments

  • Drying granules after washing

  • Drying filter cake for further processing

 

Common questions

Rotary or tray dryer, which suits my product?

Rotary dryers suit free-flowing material in continuous volume. Tray dryers suit small batches or material that must not tumble.

 

What temperature does the dryer run at?

Most chemical drying is done at ambient to 150°C. We set the limit from the highest temperature your product can take.

 

What burner size is needed?

It depends on water to be removed per hour. One recent zinc dryer used a 2,00,000 kcal/hr LPG burner.

 

Is the drum stainless steel?

Yes. Drums are SS-304 or SS-310.

 

How is dust controlled?

We size a cyclone or filter at the exhaust to suit your powder.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page