top of page

Home  /  Products  /  Hot Room

Hot Room

Insulated walk-in hot air drying room with heaters or gas hot air generators, blowers and moisture exhaust.

Also called a hot air drying room, industrial drying room, drying chamber, walk-in oven or walk-in drying room; known locally as a garam kamra.

Key Features

  • Separate temperature control in each cabin

  • Safety thermostat backs up each controller

  • Moisture exhaust in every cabin

  • Humidity indication

  • Motorised doors for trolley access

  • Built on site to fit your shed

  • Electric, LPG/PNG or dual fuel heating

Specifications

Typical working range: ambient to about 100°C; higher on request

Example room size: 31 × 14 × 8 ft

Cabins: 5, each 6 × 14 ft (custom)

Frame: 2 inch square MS pipe, 1.6 mm

Insulation: 50 mm rock wool on all sides

Wall covering: 8 mm HDHMR board both sides

Heating: hot air generator per cabin, e.g. 4.5 kW finned heaters with 1 HP blower; or LPG/PNG; or dual fuel

Exhaust: one fan per cabin

Doors: motorised vertical lift

Control: temperature controller, safety thermostat and humidity indicator per cabin

Industries: Welding electrodes, foundries, coatings, electrical repair and manufacturing

About the Hot Room

A hot room is an insulated room, or a set of cabins, heated with recirculating hot air and used to dry or warm large quantities of product on trolleys and racks. It typically runs from just above ambient to about 100°C, with higher temperatures on request. It is a hot-air drying room, not a low-humidity dry room of the kind used for lithium battery or pharma clean rooms.

 

A recent AHS hot room for air drying of electrodes measures 31 × 14 × 8 ft and is divided into five cabins of 6 × 14 ft. The frame is built from 2 inch square MS pipe, insulated with 50 mm rock wool on all sides and covered on both faces with 8 mm high-density moisture-resistant board. Each cabin has its own hot air generator with 4.5 kW finned heaters and a 1 HP blower, an exhaust fan for moist air, a humidity indicator and a motorised door that lifts vertically.

 

The control panel holds a temperature controller and safety thermostat for each cabin, exhaust fan and door controls, and heater and blower indicators. Foundation and civil work for the room can be included in the AHS scope.

 

Uses go beyond electrodes. Foundries dry cores, moulds and coatings, where forced hot air typically cuts drying from many hours to well under an hour. Motor and transformer repairers dry windings slowly, typically holding around 90–105°C for several hours and raising temperature only a few degrees per hour. Painted and resin-coated parts can be dried or force-cured in bulk. AHS has supplied hot rooms and hot room upgrades to electrode makers, heated by electric heaters, LPG or PNG hot air generators, or dual fuel, and built to your shed size.

 

Typical applications

  • Air drying of welding electrodes before baking

  • Drying of foundry cores, moulds and coatings

  • Drying of motor and transformer windings

  • Drying and force-curing of painted and resin-coated parts

  • Pre-heating and storage of materials

  • Bulk drying of trays and trolleys

 

Common questions

Is this a dry room for lithium batteries?

No. An AHS hot room dries products with recirculating hot air. Low-dew-point dry rooms for batteries need dehumidifiers and are a different product.

 

What temperature can a hot room reach?

Most hot rooms typically run from just above ambient to about 100°C. Higher temperatures can be built with thicker insulation and suitable panels.

 

Can you build it inside my existing shed?

Yes. The room is built on site from an MS frame and insulated panels to fit the space.

 

Can each cabin run at a different temperature?

Yes. Each cabin has its own hot air generator and temperature controller.

 

How is moisture removed?

Each cabin has an exhaust fan, and humidity indicators show when moist air needs to be vented.

 

Electric, gas or dual fuel?

All are possible. Electric heaters suit smaller rooms, LPG or PNG hot air generators suit large rooms, and dual fuel adds backup.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page