top of page

Home  /  Products  /  Aluminium Utensils Dryer

Aluminium Utensils Dryer

Conveyor or batch dryer that removes water from utensils after washing or pickling, before stains form.

Also called a utensil drying machine, utensil dryer oven or bartan dryer.

Key Features

  • Continuous drying straight off the washing line

  • Air directed inside hollow pieces

  • Variable belt speed for different sizes

  • Moisture exhaust keeps the tunnel dry

  • Gas or electric heating

  • Batch version for mixed small lots

Specifications

Working range: typically 80–150°C (higher on request)

Type: conveyor dryer or batch trolley/rack dryer

Conveyor drive: 1 HP DC or VFD variable speed

Gas heating: LPG/PNG/CNG burner in a separate firing chamber

Electric heating: option for sites without gas

Insulation: 75 mm mineral wool

Airflow: recirculation fans with moisture exhaust

Controls: digital PID with burner-fail alarm

Industries: Aluminium and steel utensils, cookware

About the Aluminium Utensils Dryer

After forming, aluminium and steel utensils are cleaned. Many aluminium utensils are also pickled, which means dipped in an acid or alkaline bath to remove oxide and give an even surface, and then rinsed. Utensils left to dry in the open develop water marks and patchy oxidation, and stacks of wet pieces hold up packing. A utensils dryer blows heated air over and inside every piece, so it leaves dry, clean and ready to pack or coat.

 

AHS builds utensil dryers in two forms. The conveyor dryer suits continuous washing lines: utensils ride on a belt through a heated tunnel and drop off dry at the exit. One standard build uses a single gas burner in a separate firing chamber, a 1 HP DC variable-speed drive and 75 mm mineral wool insulation. Batch dryers use trolleys, trays or racks and suit smaller units or mixed sizes. We have supplied utensil dryers to utensil makers across India, and an electric conveyor dryer for a buyer in Nepal. Heating is LPG, PNG or CNG through a firing chamber, or electric.

 

This dryer only removes water. For curing non-stick coatings on cookware, see also our Non-Stick Curing Oven, and for softening circles before forming, see the Circle Aluminium Annealing Oven. Together they cover the main heat processes in a utensil plant. Tell us the largest utensil size, pieces per hour and whether you load from a washing line or by hand, and we will propose belt width, tunnel length and heating.

 

Typical applications

  • Drying aluminium utensils after pickling and rinsing

  • Drying steel utensils after washing

  • Drying pressure-cooker bodies and lids

  • Drying utensils before coating or packing

  • Drying washed circles and blanks

 

Common questions

Why use a dryer instead of air drying?

Air drying leaves water marks and patchy oxidation, and takes up floor space. A dryer gives clean, dry pieces in minutes.

 

What is pickling, and why does it matter for drying?

Pickling is dipping utensils in a chemical bath to clean the surface. After rinsing they must be dried quickly to avoid stains.

 

Conveyor or batch dryer?

A conveyor suits a continuous washing line. A batch dryer suits smaller output or mixed sizes.

 

Can it run without gas?

Yes. We build electric utensil dryers, including an electric conveyor dryer we exported to Nepal.

 

Can the same machine cure coatings?

No. Coating cure needs much higher temperatures. See our Non-Stick Curing Oven.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page