top of page

Home  /  Products  /  Barton Pot Furnace

Barton Pot Furnace

Gas fired furnace body that heats the Barton pot for making lead oxide for batteries.

Also called a Barton furnace, Barton oxide furnace or lead oxide pot furnace; known locally as a Barton bhatti.

Key Features

  • Even heating of the Barton pot

  • Drain chute for safe handling of a pot leak

  • Gas burner with chimney

  • Panel includes stirrer motor starter

  • Matching Barton melting furnace available

  • Built to your pot drawing

Specifications

Example pot: 1,550 mm diameter × 1,000 mm deep (customer scope)

Furnace body: 2,122 mm diameter × 1,311 mm high

Top flange: 2,310 mm diameter

Operating temperature: 400°C

Heating: 1 gas burner (LPG/PNG)

Insulation: 100 mm ceramic fibre and mineral wool on sides; 50 mm castable bottom

Leak drain: 150 × 150 mm chute

Chimney: 100 mm, insulated

Control: burner control, temperature controller, stirrer motor starter

Industries: Lead-acid batteries, lead oxide

About the Barton Pot Furnace

In a Barton process, molten lead is fed into a pot where fast stirrers break it into droplets and air oxidises it into fine lead oxide for battery paste. The pot must be heated to start the reaction and held at a steady temperature, so the furnace around it has to give even heat and safe containment.

 

An AHS Barton furnace built for one lead oxide plant takes a pot of 1,550 mm diameter and 1,000 mm depth. The furnace body is 2,122 mm in diameter and 1,311 mm high, with a 2,310 mm top flange, a 12 mm top plate and 5 mm bottom and side plates. It runs at 400°C on one gas burner. Side walls carry 100 mm ceramic fibre (128 density) and 150 kg/m³ mineral wool, the bottom has 50 mm refractory castable, and a 150 × 150 mm drain chute is provided to take molten metal away safely if the pot ever leaks.

 

A 100 mm insulated chimney carries away flue gas. The control panel holds the burner controls, the temperature controller, the stirrer motor starter, mains isolator and protection MCBs.

 

AHS also makes a smaller Barton melting furnace that melts the lead feed, with a 550 mm diameter, 485 mm deep pot. As with all our lead furnaces, the pot and stirrer are normally supplied by the plant, and the furnace is built to their drawing.

 

Typical applications

  • Leady oxide for lead-acid battery paste

  • Battery oxide plants

  • Lead oxide feed for red lead furnaces

  • Replacement furnace bodies for existing Barton pots

  • Oxide plants for inverter, UPS and e-rickshaw batteries

 

Common questions

Do you supply the Barton pot and stirrer?

Usually the pot and stirrer are supplied by the plant or its process designer. AHS builds the furnace body, insulation, burner and panel to match.

 

What temperature does the furnace run at?

AHS Barton furnaces are built for about 400°C operating temperature.

 

What happens if the pot leaks?

The furnace has a 150 × 150 mm drain chute so molten lead can run out safely instead of collecting in the insulation.

 

Can you also supply the lead melting furnace?

Yes. AHS makes a Barton melting furnace and lead melting pot furnaces to feed the Barton pot.

 

Can it be electrically heated?

Gas firing is standard. Electric heating can be discussed for your site.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page