top of page

Home  /  Products  /  Pit Type Annealing Furnace

Pit Type Annealing Furnace

Top-loading pit furnace with SS pot and charge carrier for annealing wire coils and strip coils.

Also called a pot annealing furnace, pit furnace for wire coils or coil annealing furnace; known locally as a pit annealing bhatti.

Key Features

  • Top loading for heavy coils

  • SS pot and charge carrier supplied as a set

  • Lid-mounted fan for even heating of dense coils

  • Three heating zones on the wall

  • Water-cooled fan bearing for long life

  • Replacement pots and carriers available

  • Door switch and heater protection

Specifications

Construction: MS shell with SS inner pot

Heating load: 90 kW (3 × 30 kW) or 120 kW (3 × 40 kW); up to 160 kW for large pits

Heaters: sealed heaters or Kanthal coil on inner walls

Insulation: 200 to 250 mm ceramic wool and mineral wool

Circulation: 450 mm SS-304 lid fan, 2 HP, water-cooled bearing housing

Charge carrier: SS, made to coil size

Lid: crane or hydraulic lift-and-swing

Control: automatic on/off or PID with SCR, soak timer and hooter

Typical cycle: about 4 hours (charge dependent)

Industries: Wire drawing, cables and conductors, welding consumables, metal strip

About the Pit Type Annealing Furnace

A pit type annealing furnace is loaded from the top. Coils of wire or strip are stacked on a charge carrier, lowered by crane into a stainless steel pot inside the pit, and heated with the lid closed. Loading from above keeps heavy coils from sagging and makes good use of floor space.

 

AHS pit furnaces have a mild steel shell, an SS inner pot and sealed heaters on the inner wall, typically 90 kW in three 30 kW zones or 120 kW in three 40 kW zones. 250 mm of ceramic wool insulation keeps losses low. A 450 mm SS-304 fan in the lid, driven by a 2 HP motor with a water-cooled bearing housing, circulates air through the coils for even heating. The panel switches heating on and off automatically at the set temperature and has a soak timer and hooter. A typical cycle is around 4 hours, depending on charge.

 

Larger AHS pit furnaces have used work baskets of 2,200 × 1,500 × 1,700 mm, 160 kW Kanthal coil heaters, a hydraulically lifted lid and an SS baffle wall to guide airflow.

 

AHS has supplied complete pit furnaces with pot, lid, fan assembly and SS charge carrier, along with replacement pots and carriers, and aluminium wire annealing ovens to wire makers. Spares can be supplied for export.

 

Typical applications

  • Aluminium wire and rod coil annealing

  • Copper and steel wire annealing

  • Welding wire annealing

  • Strip coils and binding wire

  • Electrical stampings and small coils

 

Common questions

What size charge can the furnace take?

Pot diameter and depth are made to your coil sizes and the number of coils per charge. Tell us the coil OD, ID, height and weight.

 

How long is an annealing cycle?

A typical AHS wire annealing cycle is about 4 hours including soak, but it depends on coil weight, alloy and temperature.

 

Why is there a fan in the lid?

Coils are dense and heat slowly at the centre. The fan forces hot air through the coils so inner and outer wraps reach temperature together.

 

Can I buy only a new pot or charge carrier?

Yes. AHS supplies replacement SS pots and charge carriers for its pit furnaces.

 

Can I anneal copper bright?

Bright annealing needs a sealed pot with protective gas or vacuum. Tell us your finish requirement and we will advise the right pot and seal.

 

Related ovens and furnaces

 

Need a quotation? Share your load size, working temperature and fuel, and we will suggest a design. Call +91 98105 20120, message us on WhatsApp or send an enquiry. For a quick figure first, try our oven heat load calculator.

bottom of page